A no-compromise cartesian 3D Printer designed for speed and precision, created as a long-lasting platform for those who like to push quality and speed to the extreme.
~ A community-driven project ~
Status: V1.0
Sponsored by JLCPCB Flexible Heaters - Custom Flex Heaters for Your Build
(at BOM Spec)
- Cross Frame design focused on stiffness and stability with a low center of gravity
- Streamlined frame assembly consisting of only six extrusions
- Lightweight bed carriage assembly with carbon fiber components
- AWD stepper configuration for the Y-axis
- Optional conversion for X-axis AWD setup
- 235 x 235 x 200 mm maximum build volume (easily expandable to other sizes)
- (200 mm)^2 Carbon Fiber Bed for high-speed setup
- (235 mm)^2 bed support for a larger volume
- Optimized for daily print speeds of 400-600 mm/s with 20.000 mm/s^2 acceleration (Test A) (Test B) (Test C)
- Motion system capable of 1.000 mm/s speed with 100.000 mm/s^2 acceleration (Test)
- Maximum volumetric flow rate: ~55-60 mm^3/s (Test A) (Test B)
- Built using 30 series T-slotted extrusions with parts up to 3090
- All bracket assembly
- Genuine high-quality motion system components (BOM)
- Entire motion system based on high preload MGN12H linear guide rails
- Fully belt-driven with minimal belt paths
- 9mm 2GT belt in symmetrical configuration for the Y-axis
- 6mm 2GT belts for the rest of the axis
- Independent Z stepper motors with Z Tilt capability for the X-axis
- Lightweight dual plate Carbon Fiber Bed Carriage with integrated tensioner and compatible with different bed sizes and carriage configurations
- Rigid carbon fiber bed mount
- Lightweight Polyimide flex PCB 200W Bed Heater
- Double shear shaft supports for Y and X axis steppers
- High torque LDO-42STH48-2504AC stepper motors supplied with 36V for the X and Y-axis
- Dual power supply supporting 24V and 36V power standards (easily configurable for 48V)
- Driven by the Octopus Pro 1.1 board with TMC2240 drivers
- Running Klipper/Kalico firmware
- Fully featured Klipper Configuration and Slicer Profiles available
- Easily serviceable External electronic box with good airflow, and support for multiple power supplies, SSRs, RPi and large controller boards.
- Good cable management with a quick disconnect Breakout Board between the printer and ebox
- Toolhead based on the Dragon HF hotend and HF extender
- Alternate hotends supported: Dragon UHF, Ace, Mellow NF-Crazy-Volcano HF, Rapido, Goliath (User Mods)
- LDO Orbiter 2.5 direct drive extruder
- Sherpa Mini supported (User Mods)
- Dual 5015 fan setup for part cooling
- Dual AUX cooling modules based on 9733 blower fans providing 64 CFM of auxiliary cooling
- Adopts the Annex Engineering Quickdraw Probe
- Zero Y offset probe placement for no gantry twist deviation
- Full bed probe coverage
- Minimalistic printed part design focused on strength and easy printability
- Printed in ASA, providing high temperature resistance
- Easily enclosed, with the main electronic components outside of the build chamber.
- The (200 mm)^2 bed configuration can be fully enclose up to the frame bounding box, with no extra space needed for the bed movement. (Dimensions)
Resonance Tests:
-
This project can be self-sourced by following the BOM Guide.
-
An official upgraded LH Stinger - Rev2 Kit is produced and sold by FYSETC.
- Phaetus Dragon UHF - Hotend
- FYSETC Sherpa Mini - All Metal - CNC Extruder
- MGN 12H Z1 Preload Linear Rails
- FYSETC Spider V3.0 H7 (550Mhz) High Voltage board
- 48V Power with TMC5160 Drivers (AWD Y, X Axis)
- High Torque 2.5A 580mN.m Stepper Motors with 30mm shafts for double shear support
- Delta (48V) and Meanwell (24V) PSUs
- Carbon Fiber Bed with Pre-applied PI Heater and Pre-epoxied CF Carriage Assembly
- LHS Breakbeat distribution board and wiring harness
You require: The Printed Parts and a BTT Pi V1.2 or Raspberry Pi SBC (Klipper Host)
Use the code FYSBKSALELH for a total of $699. Free shipping directly from US/EU.
A portion of every kit sale goes towards supporting the project! 💜
- Assembly Guide
- STL Files and Printing Instructions
- CAD Source Files
- Klipper Configuration
- Build Log
- Videos
-
The LH Stinger Wiki is a regularly updated and intended to serve as your primary point of reference during the build
-
The main body of documentation can be found in the Assembly Guide
For additional support please join us on the LH Stinger Discord
- Enclosure (In progress) by zwirbel
- An extensive range of community mods available
lemurshaze @ gmail.com
@LH on LH Stinger Discord
Thanks to everyone in the LH Stinger community who supported the project, contributed in any form, or provided feedback! 💜
Inspired by the Annex Engineering team and community, along with the Klipper community, RatRig and all the crazy people that continue to push bed slingers to their limits. 💜
-Toolhead evolved from an amazing design by Dalegaard
-Silicon sock mold based on Renátó Kulman
-Wago 221 mounts by fns720
-SSR protection cover based on Technoturk
-3030 extrusion Cable clip based on Arthur_C
-3030 t-nut clip based on John_S
Special thanks to those who donated to this project throughout its development! 💜
djezo888. Fen, Budz, techb0i, PinGZ, abstractFlo, BeccaK, Steven @crydteam, Robin @crydteam, Fred Bernton, Mawoka, rmxbit, Mcclane, malar6606, EMMY BEAR 3D, Killa_Prints, Michel, vr6deezy, Ajax240, Zemlos01, popster, Dan, Sibert, Ultracopa, yoske, Arjun, iKuro
If you would like to give your support, please use the link below:
This work is licensed under a Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike
